This “princess” has discovered something under her mattress.

Making the mattresses:
1. Make a pattern by laying a piece of salvaged packing paper on the top of the bench. Run the edge of a crayon around the edge of the bench: marking on the paper the outline of the bench shape. If your bench is rectangular in shape then your job is easier: just measure your bench.
2. Add about ¼ inch all the way around to allow for the loft of the mattress and another ¼ inch for the seam allowance.
3. The mattresses are made like basic pillows.
4. To fill mattresses, I encourage you to use recycled materials.
-an old comforter: layer the pieces to achieve desired loft
-stuffing from salvaged pillows
-recycled fiber stuffing (I’ve only seen this sold in bulk). or even dryer lint. (try asking at industrial drying places for large amounts)
-down from salvaged comforters or jackets

The top blue mattress (picture above) has been given a quilted look by tying it off at regular intervals with super soft alpaca yarn (left over from knitting project).

This mattress was made from scrap fabric from another project. It is filled with two layers of an old comforter of ours that had become faded and torn. It is made like a basic pillow then I hand quilted it using embroidery floss.

This mattress was made from a cotton thrift store shower curtain (not the liner). I used the curtain’s own hem to edge it.

This mattress was made from a second hand tablecloth with a bleach stain on it. No problem, I was able to use the un-stained piece. It was made like a basic pillow then I machine sewed all around the edge. It is filled with recycled fiber stuffing.

This mattress was made from left-over fabric from the curtains I made for that room. Although this fabric was not recycled, the stuffing is. Inside is two layers of an old but clean comforter.

So far I’ve made 6 mattresses for our bench. This pile of mattresses will continue to grow as I come across other fabric to recycle.

Find out more about the bench and tips on how to alter it:
Thrift Store Coffee Table Turned Princess And The Pea Inspired Bench: Altering Bench

Bookmark It

Gossiping robots -These were made by two guests at party.

I designed this game because I wanted the kids to have something fun to do at my daughter’s 9th birthday party. In addition, I wanted to give out party favors but wanted to avoid the usual candy and plastic stuff.

Even the girls loved this robot building game. It generated lots of laughs and the kids liked that they could take their creation home.
Game rules
Using one dice, roll to see what number you get. Start with the birthday boy or girl and then continue around the table.
If you roll a one, pick out a body and pass the dice to the next player.
If it’s a two, pick out eyes and pass the dice to the next player.
If it’s a three, pick out a nose and pass the dice to the next player.
If it’s a four, pick out a head and pass the dice to the next player.
If it’s a five, pick out a mouth and pass the dice to the next player.
If it’s a six, pick out arms and pass the dice to the next player.
Bonus: If you roll the same number as the previous player, pick out an extra part. You might want to find something to be the ears, hair, eye brows…
Note: If you roll a two and you already have a set of eyes just pass on the die. There is no limit to the number of extras you can choose; as long as you are lucky enough to roll the same number as the previous player’s roll.
Game set up:
You will need to set up 7 trays; one for each number plus one more for extras. Find “trash” for the parts. Get enough for each player plus a few (for variety sake).
Body (one): olive oil cans, large cans…
Eyes (two): bottle caps, nuts, bolts, misc…
Nose (three): misc…
Head (four): cat food or tuna cans…
Mouth (five): misc.
Arms (six): thrift store silverware, electrical wire…
Extras: electronic wires,…

Robot Part Trays
Children have artistic freedom. If they want the eyes to be on the side of the head, they should put them there. These robots develop a personality of their own. Make up a name for each. The first person to finish gets a small prize. The game continues until all the guests finish their robot. Some of the bots look like robot people and some resemble animals, some are clown-like and others are aliens.
After the children have designed their robot, you will need to glue on the parts while the kids move on to another activity. I used a glue gun which worked with most of the parts (avoid really heavy items). I also used magnets to hold some of the pieces. (The head attaches well to the olive can with a magnet.)
If you want to restrict your pieces to things that a magnet will stick to, you can make a Mr. Potato Head -like toy (We named it Mr. Bolt or Mrs. Washer.)The fun being that you can rearrange the pieces to make different faces. Just glue a magnet to the back of each piece.

More robot fun coming soon.

Bookmark It

Be creative and make your own dove embellished wedding gift wrapping. This white gift wrap is really “green.”
You can find supplies for this project in a surprising variety of sources. Bumper stickers often have a really nice glossy white side and the back is often white paper that you can trace a stencil on. Another thing works well if you come across any is thin white plastic that is stiff yet thin enough to cut. I found a white plastic tray from a game. You can also find white cardboard in packaging from dress shirts to toys. You could go out and buy some white paper/ cardstock but that wouldn’t be a challenge and you would miss the point. I save all kinds of white product packaging and other waste materials and used the best pieces for doves.

The paper I used for this dove was stiff: I wanted it to stand up for a 3D effect that would take the place of a bow. To hold the dove in place: I cut out a rectangle, folded it in half and glued half onto the back of the dove. The other half of the rectangle can be slipped under the ribbon and discreetly glued or taped to the wrapping paper.
I wrapped this gift in discarded office paper (poster size). The other side had last month’s office presentation on it. It was too good to waste.

Use a nice quality ribbon to add a touch of color. It can later be used on another gift or reused in some other project.

Dove gift tags
To make a gift tag, you will need to fold scrap paper and place the stencil along the fold so that the top of the head and part of the wing will be on the fold. Write a message of love and peace. Use salvaged paper that is about the thickness of card stock. I’ve provided stencils of two different doves that I sketched.

This is far from looking like trash.

dove A stencil

dove B stencil

Bookmark It

This protective sketchbook pouch made out of salvaged jeans is a great beginner sewer project.

1.
Find a pair of pants that are worn in the knees. Cut off one leg at the knee. Keep in mind that the width of the pant leg will determine the width of your pouch. Therefore use children’s pants if you want a small pouch.

2.
Think about what you want to put in your pouch: sketchbook, journal, phone/ address book, or diary. I put a sketch book on top of the leg to help gauge the size pouch needed. Make sure you leave room on the bottom for the seam. I cut off the bottom edge of the pants but you can leave it on if you like.
If the pants you are using are a straight leg, you may want to use the bottom edge of the pants at the top edge (This edge will end up on the front of your bag as the flap edge. The pants that I used had a little flare at the bottom and I liked the shape it gives to it.
Also determine the length you want the flap to be and cut.

3.
Lay your piece flat and face up, then cut out the front part of the pant leg where the flap is (see image). The back of the pant leg will flip forward and become the flap.

4.
Turn your pant leg inside out and sew the bottom seam or don’t turn it inside out and just sew across, leaving the seam on the outside (as seen in photo).
Also, decide on the shape you want your flap and cut. You can leave the edges raw so they will fray or you can turn the fabric under and sew. The jeans that I used had some stretch to them and I found out that they don’t fry as well as traditional 100% cotton jeans.

5.
Add button, snap or recycled jean button. I re-used a button from a pair of button fly jeans. When you cut it off the jeans, leave it attached to some of the jean fabric. I left it on a 1.5 inch square piece of jean fabric.
Mark where you want the jean button (if using) and make a small straight cut. Then, mark the position of the hole below by making a mark through the first hole. You should now have two holes lined up with each other and just big enough for the button. Do not make a hole in the back of your pouch: just a hole in the flap and in the front part of your pouch.
If using a regular button, you will still need to clip a small hole in the flap and mark the position below. Instead of cutting a second hole, sew on a button to the front of the pouch. Keep your eye out for fun vintage buttons for using in projects like this.

6.
From the inside of the pouch, put the jean button into the hole (see image). I didn’t think it was necessary but if your button is loose, you may want to add a few stitches to hold the button in place (sewing, fabric to fabric, a circle around the button).

7.
To close the flap, put the button through the flap hole.

8.
Here is a closer look at the button I used in this project. It was salvaged from a pair of button-fly jeans.

9.
Add a slot that will give you easy access to a pen or pencil. Cut a small hole just large enough for a pen or pencil to slip through (see arrow in photo). Only cut through the front of the pouch! Next sew a channel about ¾ of an inch from the edge of the pouch (see white line in image).
10.
That’s it, you’re done. Put in your notebook and your pencil and you are ready for a nature hike.
Also see other ideas for pant leg pouch, bag, or purse. Link

Bookmark It

This clever little pink pouch was designed by an eleven year old (my daughter). She independently came up with the idea to recycle the bottom part of a pair of old pants to make a pouch/ bag.
This project is simple enough to do at a children’s party. Kids will love designing their own unique pouch.

This pouch could also be used to hold your Valentine card collection. Do you have a collection of special Valentine cards already started? They would fit nicely into a home-made pouch. My daughters each have a small collection of valentine cards that grows each year.

Add a strap if you would like to make this pouch into a purse.

I think a pant leg pouch/ bag would make a wonderful eco-friendly gift wrapper too: place gift inside.
I used the design of this pouch and took it a little further: See my post for instructions on how to make a jean sketch book pouch.

Bookmark It

How to:
Use a good pair of garden shears to cut some straight branches. From these branches, cut 5 stick pieces the same length and approximately the same diameter. Cut the first stick (whatever looks right) and use that stick to mark the length of the remaining sticks. I used sticks that were about 6 ¼ inches long and ¼ to nearly ½ inch wide. The exact size doesn’t matter as long as it appeals to your sense of proportion and all the sticks are the same length. Keep in mind; thinner sticks are easier to bend into place.

Tie two sticks together than tie another two sticks together near the end (see X and Y in photo).
Spread out the non-tied ends and overlay as in photo and tie top of star (see Z in photo).

Tie on the last stick. Play with the sticks a little; some go over, some under. Do whatever works for that star.

Party Craft
I prepared enough for my daughter’s whole class. I made bundles and tied them together with nice red yarn that was used to hang the star ornament after the star was constructed. The ball of wool yarn was used to tie all the sticks together.

Bookmark It

I made this box from a brightly colored poster found at a garage sale. It was damaged but I only needed part of the poster to make the box.
Cut the bottom square ¼ inch smaller than the top square. (I used an 8.5 inch square to make the top and an 8.25 inch square to make the bottom.

Remember to line up corners and sides exactly and run the back of your nail across the folds.
1. To make this origami box you will need a perfectly square piece of paper. A paper cutter works great but if you do not have one you will need to measure carefully and then cut with scissors.
2. Before doing your first fold, place your square so the back side is up (the good side is face down). Then bring opposite corners together and make a nice crease.
3. Unfold and bring other opposite corners together and make a nice crease.
Your paper should now have fold lines in the shape of an x.
4. Again, with the back side up, fold your paper in half vertically.
5. Unfold. Fold paper in half horizontally. This means fold the bottom corners up to the top corners. (I forgot to take this picture: sorry.)
6. Unfold. Next fold in one of the corners. Point the corner to the exact center of the paper. You will know where that is by looking at the fold lines that you already made.
7. Fold in another corner.
8. Fold in another corner.
9. Fold in last corner.
10. Fold the bottom up to the center as shown in the picture.
11. Fold the top: they should meet in the center.
12. Unfold. Fold one side to the center.
13. Fold the other side. They should meet in the center.
14. Unfold last two folds. Pull open opposite corners.
15. Fold up two (opposite) sides. These will be two of the sides of your box.
16. To finish your box you will have to fold the paper in as shown.
17. I thought another view might be helpful. This is the hardest step to figure out. Hold your soon- to-be box top in the same orientation as shown in the photo and you should be fine.
18. Bring the corners up and around to the inside.
19. Completed box top.
20. Follow the same instructions to make a bottom for your box; remember to cut the square for your box bottom ¼ inch smaller that the square you cut for the top of your box.

Project ideas: Valentine card reused to make origami box, vintage Valentine embellished origami box, and magazine page made into Valentine gift box.

Bookmark It

How to:
Set aside suitable single serving milk bottles. Make sure you wash them out really well; old milk smells really bad. I got these bottles at Chick-Fil-A. If you don’t eat at that restaurant, ask all your friends to save them for you or find a similar bottle elsewhere. Depending on your needs, you may want to start collecting well in advance. (I’ve been known to save all year or longer for projects.)

Paint on the faces with black acrylic paint and let dry. Alternatively this might be an activity for guests at your Halloween party. Even young children can do this simple craft. Make a few in advance to set out as examples. I accidentally discovered that if you paint the face and let it dry a little but not all the way, you can use your brush to slide around the paint to make even scarier faces.

Print out ghostly messages on your computer, cut into strips and glue to the bottom of each bottle (See photo.) Write “Find a trick or treat inside. Maybe both”. Or write ” No trick, there is a treat inside!”
For fun, you may want to surprise your guests with a “trick” inside. Take a strip of paper and fold it accordion style with the word “Boo!” at the end. Glue the other end to the inside of the bottle cap. Children will find it when they open their bottle.

Fill these Halloween themed party favors with gummy worms or other treats.

Bookmark It

For detailed instructions including ball stencils, check out my post called How To Make Fun Recycled Sweater Beach Ball Pillows.

Be creative and design your own leaves or use the Leaf Stencils for Produce Pillows

To make the leaves on these clever pillows you will need to score a wool sweater from a thrift store, friend or yard sale. It is not uncommon for people to accidentally felt their sweaters by machine washing with warm or hot water. During the felting processes, the sweater will shrink; thus, they end up at donation spots. Sweaters with a hole or stain can easily be worked around. Another good idea is to use an old army green wool blanket. I didn’t use it for any of these leaves but it works great.

Felting Wool Sweaters
You can intentionally felt old sweaters by putting it in the washing machine and wash with hot water and detergent. Not much to it.

Delicious looking Red Apple Pillow
To make an apple pillow, you will need a red sweater or a T-shirt, a scrap piece of a brown sweater and a small piece of a green felted wool sweater. Follow the general instruction on how to make a beach ball pillow only sew on a green leaf cut from the wool sweater. Felting instructions above.

Vine-Ripe Tomato Pillow
To make a tomato pillow, you will need a tomato red sweater or a T-shirt, and a few small pieces of a green felted wool sweater. I used a very thin red sweater. Follow the general instruction on how to make a beach ball pillow then sew on three green leaves cut from the wool sweater. Felting instructions above.

Berry Blue Blueberry Pillow
To make an blueberry pillow, you will need a blue sweater or a T-shirt, a scrap piece of the blue sweater for the top circle and a piece of a blue felted wool sweater. Follow the general instruction on how to make a beach ball pillow only sew the circle on top of the felted piece as in the picture. Felting instructions above.

Autumn Pumpkin
To make a pumpkin pillow, you will need an orange sweater or a T-shirt, a scrap piece of a brown sweater and a small piece of a green felted wool sweater. Follow the general instruction on how to make a beach ball pillow only sew on a green leaf cut from the wool sweater. Felting instructions above.

Orange Grove Pillow
To make an orange pumpkin pillow, you will need an orange sweater or a T-shirt, a scrap piece of a brown sweater and a small piece of a green felted wool sweater. Follow the general instruction on how to make a beach ball pillow only sew on a green leaf cut from the wool sweater. Felting instructions above.

Bookmark It

I made a whole bunch of these pillows; they make great gifts!

Add a little fun to your home decor. Perfect for children’s rooms!

Using the right sweaters you can create a pillow with a nautical or patriotic look.

 How-to:
1. Set aside unwanted or damaged sweaters in desired color(s). Keep in mind that thinner sweaters are easier to sew.

2. You will need a Beach Ball pattern.*

*Because it takes a tremendous amount of time for me to develop projects like this, design and draw a pattern, test ideas, make, take pictures, edit pictures, write the how to, etc… I’m asking for a mere 2 dollars (see side donation button for quick payment with paypal). E-mail me and I’ll e-mail you the pattern in two sizes (large and small).

 Print out the ball stencil that I made and use it to make your own stencil out of a cereal box or other scrap cardboard.

Size: The large ball is about 11 to 12 inches tall and the small pillow is about 6 inches tall. The size of your pillow will depends on how stretchy the fabric is and how much you stuff it.

3.

Use your stencil, a rotary cutter, and a cutting matt to cut out the pieces of the ball. If you don’t have a rotary cutter yet, trace the stencil and use fabric scissors to cut them out. You will need 6 pieces per pillow. In addition, you will need two small circles: one for the top and one for the bottom. I just free hand cut the circles two at a time so they are the same size. Alternatively you can trace a small glass or other small round circular item. Keep in mind that the circles have to be bigger than the desired finished size because the raw edges are turned under.

4. Lay out the pieces in a flower shape to help you visualize the pattern and to see how the colors look together. I suggest you find 3 colors that look nice together and then cut 2 pieces of each color or pick 6 colors one piece of each color.

5. Stack the pieces in the pattern order of your choice. Take the first two and sew (right sides together) along one side leaving about ¼ inch seam. Then sew the next piece on and the next until all 6 pieces are together. Don’t bother to place pins because sweater fabric is so stretchy and each piece might stretch a different amount. Also don’t worry if you have a bit of a hole on the top and bottom of your ball because these spots will be covered up by the circles.

6.Sew up the last seam (ball should still be inside out) leaving about 3.5 inches un-sewed.
7.Turn your ball right-side out and add stuffing through the hole you left.

8.The last part is to hand-sew the stuffing hole closed and hand-sew the “buttons” on the top and bottom. Turn under the raw edge as you sew along.

Bookmark It