Make Your Own Protective Sketchbook Pouch Out Of Jean Pant Leg

This protective sketchbook pouch made out of salvaged jeans is a great beginner sewer project.

1.
Find a pair of pants that are worn in the knees. Cut off one leg at the knee. Keep in mind that the width of the pant leg will determine the width of your pouch. Therefore use children’s pants if you want a small pouch.


2.
Think about what you want to put in your pouch: sketchbook, journal, phone/ address book, or diary. I put a sketch book on top of the leg to help gauge the size pouch needed. Make sure you leave room on the bottom for the seam. I cut off the bottom edge of the pants but you can leave it on if you like.
If the pants you are using are a straight leg, you may want to use the bottom edge of the pants at the top edge (This edge will end up on the front of your bag as the flap edge. The pants that I used had a little flare at the bottom and I liked the shape it gives to it.
Also determine the length you want the flap to be and cut.


3.
Lay your piece flat and face up, then cut out the front part of the pant leg where the flap is (see image). The back of the pant leg will flip forward and become the flap.


4.
Turn your pant leg inside out and sew the bottom seam or don’t turn it inside out and just sew across, leaving the seam on the outside (as seen in photo).
Also, decide on the shape you want your flap and cut. You can leave the edges raw so they will fray or you can turn the fabric under and sew. The jeans that I used had some stretch to them and I found out that they don’t fry as well as traditional 100% cotton jeans.


5.
Add button, snap or recycled jean button. I re-used a button from a pair of button fly jeans. When you cut it off the jeans, leave it attached to some of the jean fabric. I left it on a 1.5 inch square piece of jean fabric.
Mark where you want the jean button (if using) and make a small straight cut. Then, mark the position of the hole below by making a mark through the first hole. You should now have two holes lined up with each other and just big enough for the button. Do not make a hole in the back of your pouch: just a hole in the flap and in the front part of your pouch.
If using a regular button, you will still need to clip a small hole in the flap and mark the position below. Instead of cutting a second hole, sew on a button to the front of the pouch. Keep your eye out for fun vintage buttons for using in projects like this.


6.
From the inside of the pouch, put the jean button into the hole (see image). I didn’t think it was necessary but if your button is loose, you may want to add a few stitches to hold the button in place (sewing, fabric to fabric, a circle around the button).


7.
To close the flap, put the button through the flap hole.


8.
Here is a closer look at the button I used in this project. It was salvaged from a pair of button-fly jeans.


9.
Add a slot that will give you easy access to a pen or pencil. Cut a small hole just large enough for a pen or pencil to slip through (see arrow in photo). Only cut through the front of the pouch! Next sew a channel about ¾ of an inch from the edge of the pouch (see white line in image).
10.
That’s it, you’re done. Put in your notebook and your pencil and you are ready for a nature hike.
Also see other ideas for pant leg pouch, bag, or purse. Link

One thought on “Make Your Own Protective Sketchbook Pouch Out Of Jean Pant Leg

  1. Carmen

    Thanks for sharing this idea! I love your site, BTW… I’m pretty obsessed for finding things to do with old clothes. This one is great!

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>